Home Products Networks / Communications Communication Gateways

AB7615

ANYBUS-X J1939-PROFIBUS SLAVE


Anybus X-gateway – PROFIBUS Slave - J1939


Price Per 1   £616.00

Routeco stock: 0
Non-Returnable Product
Please login or register for trade pricing.

Associated Products
^ denotes Non-Returnable Product.



Technical Specification
Depth114 mm
Front installation possibleyes
Height127 mm
IO link masterno
IP-ratingIP20
Rack-assembly possibleno
Rail mounting possibleyes
Supply voltage DC24...24 V
Supporting protocol for Data-Highwayno
Supporting protocol for DeviceNet Safetyno
Supporting protocol for DeviceNetno
Supporting protocol for EtherNet/IPno
Supporting protocol for MODBUSno
Supporting protocol for other bus systemsyes
Supporting protocol for PROFIBUSyes
Supporting protocol for PROFINET IOno
Supporting protocol for TCP/IPno
Voltage type of supply voltageDC
Wall mounting/direct mountingno
Width44 mm
Features and Benefits
  • Monitor and control data on a J1939 heavy duty vehicle network from PROFIBUS PLC system or device
  • Typical applications: Electric Power Generation, Oil & Gas, Marine, Military, Heavy Duty Vehicles, Any Diesel Engine based system supporting J1939
  • Max 500 bytes of I/O data in each direction
  • Easy configuration via the included BWConfig Windows Software. No programming required
  • Robust aluminum stand-alone housing
  • Global free technical support and consultancy
  • PROFIBUS Slave interface
  • PROFIBUS Slave settings can be made either via on-board switches, or by importing the provided .GSD file into engineering tool of the controlling PLC.
  • Complete PROFIBUS-DP Slave functionality according to extensions of EN 50170
  • Baudrate detection up to 9-12Mbit/s
  • 400 bytes total combined Input and Output table size including any status data and command registers
  • Cyclic I/O data transmission
  • Device diagnostic message transmission
  • PROFIBUS slave settings via on-board switches or vis .GSD file
  • 1x D-sub 9-pin female PROFIBUS connector
  • J1939 interface
  • SAE J1939 network interface with a unique network address in accordance to the J1939-81 specification
  • Max 496 bytes of I/O Input data and 492 bytes of I/O Output Data
  • Up to 120 PGN's monitored by Input data points
  • Up to 100 PGN's transmitted by Output data points
  • Supports J1939 network baud rates of 250K and 500K
  • Transmission and reception of all types of fixed-length J1939 messages, including PDU1, PDU2, broadcast and destination specific
  • Monitoring of DM1 (active diagnostics) and DM2 (previously active diagnostics) messages
  • Complete network address management including address claim, protection, and yield on higher priority conflict
  • Network address can be self-configurable over a range of addresses
  • J1939 Transport Protocol for transmission and reception of large messages (9 - 1785 bytes). Both connection based (RTS/CTS) and broadcast (BAM) are supported
  • Configurable CAN bus-off reset option will reset the network interface and attempt to return to online when a CAN bus-off condition is detected
  • 1x 5-pole 5.08 mm Phoenix pluggable screw connector for J1939
Resources / Data Sheets
User Manual


IMPORTANT: Please note that all product information, associated resources and links to third party websites contained within our website have been prepared solely for the purpose of providing general information only. All information is provided in good faith as a convenience to you and may be used for information purposes and guidance only and at all times in accordance with our Terms & Conditions of sale. Due to the reliance on third party data, we are unable to guarantee that the content on our sites is accurate, complete or up-to-date at any given time and it is recommended that if you are unsure if a product will fulfil all of your requirements that you always seek specialist advice from your local Routeco branch before making your selection.